The VACUUBRAND ME 2 NT is a compact, oil-free laboratory vacuum pump for filtration, gas transfer and other suitable non-corrosive applications. Its single-stage diaphragm design provides continuous vacuum operation without the oil changes required by rotary vane pumps.
With an ultimate vacuum of 70 mbar absolute (52 Torr) and a maximum pumping speed of 1.4 cfm at 60 Hz, the ME 2 NT is suitable for Canadian laboratories needing a reliable vacuum source for appropriate low-vacuum applications.
Manufacturer part number: 20730003 | Electrical: 120 V / 60 Hz | Certification: NRTL C/US
Laboratory vacuum filtration, non-corrosive gas transfer, suitable vacuum ovens, multi-port vacuum manifolds, general laboratory evacuation and research applications requiring oil-free vacuum.
| Manufacturer | VACUUBRAND |
| Model / Part Number | ME 2 NT / 20730003 |
| Pump Type | Oil-free, single-stage diaphragm |
| Pump Heads / Stages | 1 / 1 |
| Ultimate Vacuum | 70 mbar absolute / 52 Torr |
| Maximum Pumping Speed, 60 Hz | 1.4 cfm |
| Maximum Pumping Speed, 50 Hz | 2.0 m³/h |
| Electrical | 100–115 V / 50–60 Hz or 120 V / 60 Hz |
| Electrical Certification | NRTL C/US |
| Rated Motor Power | 0.18 kW |
| Inlet Connection | DN 8–10 mm hose nozzle |
| Outlet Connection | G1/4 in; silencer supplied |
| Maximum Outlet Pressure | 2 bar absolute |
| Operating Ambient Temperature | 10–40°C |
| Protection Class | IP40 |
| Dimensions (L × W × H) | 245 × 211 × 198 mm |
| Weight | 10.2 kg |
Maximum pumping speed is not the same as pumping speed at a particular operating vacuum. Check the manufacturer's performance curve when sizing a pump for a continuous gas load.
Manufacturer-supplied equipment: Assembled ME 2 NT pump, silencer, hose nozzle and operating manual.
Depending on the application, additional components may be required:
Accessories should be selected for the actual system configuration. Confirm tubing, fittings and any required moisture protection before ordering.
Choose the ME 2 NT for compatible non-corrosive gases where the pump's working pressure and pumping speed are suitable.
Consider the VACUUBRAND ME 2C NT when chemical or solvent vapour resistance is needed. Its chemistry-resistant construction is intended for more demanding chemical applications, subject to material compatibility.
Consider a multistage pump when your application requires a lower ultimate pressure than 70 mbar. The VACUUBRAND diaphragm pump range includes alternatives for different vacuum requirements.
Contact Cambridge with your required pressure, gas flow, vapour composition and operating schedule if you are unsure which model is suitable.
For continuous operation, the most important questions are:
The ME 2 NT has a published ultimate vacuum of 70 mbar absolute. That figure does not establish how much gas it can remove while maintaining 120 mbar, 200 mbar or another operating pressure.
For membrane contactors, water de-aeration systems and similar continuous applications, review the pumping curve at the required operating pressure and confirm the expected gas and moisture loads with the manufacturer.
Yes. It uses dry diaphragm pump technology and does not require vacuum pump oil.
The manufacturer describes this model as suitable for continuous pumping of compatible gases. Actual suitability depends on the operating pressure, gas load, vapour conditions and installation requirements.
Yes, for suitable filtration systems. Confirm the required vacuum level, pumping capacity and protection against accidental liquid carryover before use.
The ME 2 NT is not designed as a chemistry-resistant pump. For solvent or corrosive vapours, consider a compatible VACUUBRAND chemistry diaphragm pump.
The published ultimate vacuum is 70 mbar absolute, but that does not confirm sufficient pumping capacity at 120 mbar under a continuous gas load. Review the manufacturer's pumping curve and have the full application checked before purchasing.
The manufacturer identifies part number 20730003 as an NRTL C/US configuration suitable for 120 V / 60 Hz operation. Confirm the supplied unit and nameplate requirements when ordering for your facility.
A trap or separator may be appropriate when water vapour, condensation or liquid carryover could occur. The required protection depends on the application. Contact Cambridge to review the system configuration.
There are no oil changes. However, diaphragms and valves are wear components and may eventually need replacement. Follow the manufacturer maintenance instructions and inspect the pump for leaks or changes in performance.
Not sure whether the ME 2 NT has enough pumping capacity for your application? Cambridge Environmental can help Canadian laboratories and industrial customers review vacuum requirements, gas loads, chemical compatibility and accessory options.
Tell us the vacuum level you need, what you are pumping and whether your system operates continuously. We can help confirm the appropriate VACUUBRAND model with the manufacturer before you order.
Contact Cambridge for Vacuum Pump Support